Planned finished item
This is a Cricut Infusible Ink transfer-sheet project for one Medium bag from Cosmetic Bag Blanks, item 2008211. The three-count pack contains two medium bags and one large bag; the selected medium is listed as 9 × 6.1 inches. These are product dimensions, not a Cricut art template. The sheet is pre-inked and cut, so this route uses no printer, bottled ink, or printed sublimation paper.
Cricut Cosmetic Bag Blanks, 3 ct, item 2008211; selected size: medium
Artwork requirements
Measure the medium bag's flat front
Measure the actual flat front of the selected medium bag and keep art clear of its seams; the listed 9 × 6.1 in dimensions describe the whole bag, not a decorated-area template.
- Measure the actual flat bag panel; the listed product dimensions are outside measurements, not a design template.
- Keep graphics clear of seams, edges, and the interior seam allowance. No numeric art boundary or seam inset is published.
- Keep the complete design smaller than the 12 × 10 in plate and apply it once; do not infer multi-section compatibility from the Heat Guide.
No numeric artwork size or supplier template was verified.
The selected Heat Guide names EasyPress SE by family and does not ask for press size. The BOM identifies 12 × 10 in as the chosen tool, not a Heat Guide size selection.
Bill of materials
Gather these items before you begin. Required, optional, and included items are marked below. This cut-sheet route needs a compatible cutter, the named transfer sheet, the correct cutting mat and the supported press workflow. No sublimation printer or printer ink is needed. Check the exact blank and press instructions before substituting any item.
- 1×
Cosmetic Bag Blanks, 3 ct, item 2008211
Requiredblank
- 1×
- 1×
Cricut Maker 4
Requiredother
- 1×
Cricut Black Infusible Ink Transfer Sheets, 12 × 12 in (2 ct)
Requiredother
- 1×
Cricut StandardGrip Machine Mat, 12 × 12 in, 6 ct
Requiredaccessory
- 1×
Cricut EasyPress Mat, 12 × 12 in
Requiredaccessory
- 1×
Cricut Butcher Paper, 15 sheets, 12 × 14 in
Requiredpaper
- 1×
Generic supply named in Cricut instructions; no exact SKU specified: Lint roller
Requiredaccessory
- 1×
Generic supply named in Cricut instructions; no exact SKU specified: Scissors
Requiredaccessory
- 1×
Generic supply named in Cricut instructions; no exact SKU specified: Tweezers
Requiredaccessory
- 1×
Generic supply named in Cricut instructions; no exact SKU specified: White cardstock, 80 lb
Optionalaccessory
Equipment
Cricut Maker 4
2011084
Press guidance by equipment class
These supplier instructions name a class or application; they do not verify a particular press model.
Cricut EasyPress SE — Cricut’s U.S. Heat Guide selected EasyPress SE by family name and did not ask for plate size. This class-level guidance is not a verified recipe for either the 9 × 9 in or 12 × 10 in SKU. Cricut says the design must be smaller than the chosen heat plate and applied in one press rather than in sections; confirm the complete design fits the chosen plate. The cited Heat Guide output provides no size-specific or multi-placement recipe.
- Source: Cricut, Inc.: Cricut Cosmetic Bag Blanks (3 ct), item 2008211
- Source: Cricut Help Center: Cricut EasyPress FAQ
- Source: Cricut, Inc.: Cricut EasyPress SE – 12 in × 10 in
- Source: Cricut, Inc.: Cricut EasyPress SE – 9 in × 9 in
- Source: Cricut, Inc.: Cricut Heat Guide: Infusible Ink Square Coaster and Bag Results
- Source: Cricut Help Center: How to Use Infusible Ink
- Source: Cricut Help Center: Infusible Ink FAQ
Source-scoped starting settings
Research plan: confirmation needed. Resolve the preflight questions before using these recorded settings.
infusible ink
Cricut EasyPress SE
- Temperature
- 385 °F
- Time
- 60 seconds
- Pressure
- Firm
- Preparation and prepress
- Heat Guide says preheat press to 385°F and preheat the blank for 15 seconds. The separate How-to says allow the preheated blank to cool completely before applying the design.
- Peel and transfer removal
- Conflicting Cricut directions: Heat Guide says remove liner while warm; How-to says cool completely, then slowly remove liner. See conflict note.
- Cooling and handling
- Heat Guide says cool the design and base material before handling; its separate liner-removal step conflicts with the How-to cooling sequence.
- Mirror/cut/weed the transfer sheet and trim the liner close to the design. Use a fresh adhesive lint roll over the full blank; place protective cardstock or four butcher-paper layers inside the bag.
- Use the source-specific bag sequence: place bag on mat, place protective material inside, lint-roll, cover with clean butcher paper, preheat the bag, remove top paper, let the blank cool completely, place design face down / liner side up, cover with clean paper.
- Avoid the inside seam allowance and outer seams/edges. Cricut states these can create unevenness but does not publish a numeric artwork inset. Measure the actual flat panel instead of treating the product’s listed bag size as a print area.
- Press once without sliding the EasyPress; lift slowly. Confirm the applicable finish instruction during preflight.
- Bag care: machine wash cold without bleach; tumble dry low. If ironing is needed, use medium heat without steam. Do not dry clean.
Conflicting source instructions
Cricut’s live Heat Guide says remove the liner while warm; its separate How to Use Infusible Ink article says let the project cool completely, then slowly remove paper and liner. Preserve both source instructions and do not choose one silently.
Checked .
- Source: Cricut, Inc.: Cricut Cosmetic Bag Blanks (3 ct), item 2008211
- Source: Cricut Help Center: Cricut EasyPress FAQ
- Source: Cricut, Inc.: Cricut EasyPress SE – 12 in × 10 in
- Source: Cricut, Inc.: Cricut EasyPress SE – 9 in × 9 in
- Source: Cricut, Inc.: Cricut Heat Guide: Infusible Ink Square Coaster and Bag Results
- Source: Cricut Help Center: How to Use Infusible Ink
- Source: Cricut Help Center: Infusible Ink FAQ
Ordered steps
Do not start heating with unresolved instructions. Complete the preflight checks before following this sequence.
Step 1
Before cutting or heating, confirm the liner-removal timing for this exact cosmetic bag and EasyPress setup. The dated Heat Guide says warm removal and Cricut’s separate how-to says cool removal. Check current instructions; if they still differ, ask Cricut which applies and record its answer. Do not start the transfer until that finishing instruction is resolved.
Step 2
Confirm the exact Cricut Cosmetic Bag Blanks, 3 ct, item 2008211; selected size: medium. The listed measurements describe the outside of the selected bag, not a transfer template; choose a flat area clear of seams and edges.
Step 3
Measure the actual flat panel before making artwork. Cricut gives no numeric decorated-area size or seam inset for this blank. Keep the entire design smaller than the EasyPress plate so it can be applied once, without pressing in sections. Use one medium pouch from the mixed-size pack. Keep the zipper, seam allowances, and edges outside the flat application area.
Step 4
Mirror the design and cut the pre-inked Black Infusible Ink sheet liner-side down on StandardGrip. Crack-weed it and trim the clear liner close to the art. Maker 4 is in Cricut’s Maker family; the sheet listing names the Maker family but not item 2011084 individually.
Step 5
Place the bag on a firm, even surface above the Cricut pressing mat. Insert white 80 lb cardstock or four butcher-paper layers, lint-roll the full surface, and cover with clean butcher paper. Preheat the blank for 15 seconds per the Heat Guide, then remove the butcher-paper cover and let the blank cool completely before applying the transfer as Cricut’s separate how-to directs.
Use the listed settings context.
Step 6
Place the design face down with the liner up and cover it with clean butcher paper. Keep the EasyPress still. Only after resolving preflight, follow the applicable supplier instruction. The checked U.S. Heat Guide setting is of 385°F for 60 seconds with Firm pressure. The selector names EasyPress SE by family and does not ask for plate size; this BOM lists the 12 × 10 in SKU, so verify the full measured design fits before pressing.
Use the listed settings context.
Step 7
Lift the press slowly without shifting the stack. Use the liner-removal timing confirmed with Cricut during preflight; record that source and date. After the bag is cool, follow its care instructions. If the supplier has not resolved the timing, do not begin this transfer.
Use the listed settings context.
Completion checks
The plan names the exact Cricut Cosmetic Bag Blanks, 3 ct, item 2008211; selected size: medium and its checked U.S. Heat Guide configuration; this is a cut-sheet Infusible Ink workflow, not a printed sublimation project.
Artwork is measured from the actual flat panel and checked against one sheet, the Maker cut path, and a single plate-sized application; the outside bag size is not used as the art area.
The warm-removal versus cool-removal disagreement is visible, and no physical press result is claimed.
Before any heating, record a Cricut-confirmed peel direction for this exact blank and EasyPress SE setup. The October 3, 2026 review still finds warm-liner removal in the Heat Guide and cooling before removal in the help article; do not choose one by guesswork.
Troubleshooting
- Measure the actual flat panel and reposition the art; Cricut says seam allowances can make the pressing area uneven but gives no numeric inset.
- Reduce it until the entire design is smaller than the selected plate. Cricut says not to press Infusible Ink designs in sections.
- The Heat Guide says warm removal; Cricut’s separate how-to says cool completely, then remove the liner slowly. Consult current instructions for the exact selected item instead of combining them.
Cosmetic bag plan: Cricut Infusible Ink Transfer Sheets are pre-inked and cut with a Cricut machine. No sublimation printer, ink cartridge or printed transfer paper is needed. The plan remains conditional because the supplier’s finishing instructions conflict.
Layout for this blank
Choose the actual pouch size before laying out the motif. Keep the zipper and internal seam allowance outside the pressing area; they can prevent flat contact. The mixed-size pack does not share a single artwork rectangle. The source names the EasyPress SE family without a separate plate-size selection. The listed 12 × 10-inch model is the chosen tool, not a size-specific recipe verified by the Heat Guide.
Peel direction is still unresolved
On October 3, 2026, the live Cricut Heat Guide, with EasyPress SE, Infusible Ink Transfer Sheet and Cricut Pressing Mat selected, still said to remove the liner while warm. The How to use Infusible Ink article, edited August 18, said to let the project cool before removing paper and liner. The new check used Global Site English; the earlier record preserves the U.S. selection checked September 23.
This review did not resolve the conflict. Before heating, obtain the applicable peel direction for the exact blank and press setup. The procedure and completion check keep that same stop condition; an uncertain finish is not a reason to guess.
Cost and evidence
One blank quantity is a three-piece mixed-size pack. Count the actual pouch and sheet area consumed per attempt rather than treating the whole pack as one decorated item. Enter your actual consumed-material costs in the project pricing calculator. The original diagram is a schematic, not a photograph or measured artwork template. No physical test, finished color or durability result is claimed.
For a source-documented cut-sheet route, choose the Cricut square coaster. For a printer-based route, see the Unisub hardboard coaster.
Page address: https://makepressrepeat.com/projects/infusible-ink-cosmetic-bag
Make something next
Make a Cricut Infusible Ink wine bag
Research plan: confirmation needed
Plan a tall black motif for one Cricut wine bag, with room below the drawstring channel and above the bottom seam.
View project planMake a Cricut Infusible Ink T-shirt
Research plan: confirmation needed
Make a single black motif on Cricut’s XL polyester T-shirt with a cutting machine and EasyPress. No printer needed.
View project plan